Audi A6 / S6 C7.5 Facelift Sedan (2016-2018) Clear Black Venom Custom Taillights

Black Venom Custom Taillights – C7.5 Facelift Sedan (2016-2018)

These Audi A6 C7 custom taillights are built for the facelift C7.5 sedan generation (2016-2018) and ship as a true plug-and-play replacement for the factory LED units. Every pair starts as a genuine used Audi OEM tail light core pulled from a low-mileage donor car, refinished in-house with our signature Black Venom blackout treatment – a fully transparent clear lens paired with a deep gloss-black internal frame – and resealed at the factory joint with professional-grade automotive sealant. The result is a sharper rear-end that drops the chromed factory look while preserving the dynamic turn signature Audi invested in.

If you have been searching for genuine Audi A6 C7 taillights, an Audi A6 C7 tail lights upgrade that actually fits, or simply Audi A6 clear tail lights you can install in a driveway, this is the set. They are hand-built, not mass-assembled, and they ship ready to bolt on with zero additional coding.

Why the Black Venom Style – and Why It Is More Than a Cosmetic Refinish

These Audi A6 C7 custom taillights address both the cosmetic and the well-known factory issues. Most aftermarket “custom” units on the market are shell-only swaps – the buyer gets a new housing but inherits the old LED boards, which means two problems: (1) condensation builds up inside the housing over time because the factory seal is compromised by the swap, and (2) the cheap replacement boards trigger bulb-out warnings on the cluster because they do not match the OEM current draw. We solve both with our TSB-backed condense-fix workflow.

We rebuild on the original OEM cores. Every housing is a genuine Audi 4G0907xxx-series part (outer housing 4G0907xxx with matching inner 4G0907xxx). We do not buy aftermarket shells from China. We open the OEM unit, replace the seal with a professional-grade sealant rated for automotive lighting, refinish the chrome trim to gloss black, and reinstall the original LED boards onto fresh thermal pads. This is the same workflow Audi dealers follow when addressing the well-documented C7 tail-light condensation TSB – we just apply it as a standard production step on every set we ship.

Built to Fix the Factory Condensation – and the C7.5 Face-Glow Failure

The C7.5 facelift A6 / S6 is known for two recurring issues: (a) rear-lamp condensation and standing water inside the lens after weather cycling, and (b) the famous “face-glow” LED strip failure, where the daytime-running inner LED strip develops hot spots and partial failure because the factory thermal pads dry up. Every pair of our Audi A6 C7 Black Venom taillights addresses both: new professional-grade sealant reseal, fresh thermal pads on every LED board, and a vacuum-style reseal so the housing holds positive pressure against future moisture intrusion. When you buy a set from us, you are not just buying a style upgrade – you are buying a permanent fix for the factory issues that Bimmerpost / Audizine owners have documented for years.

True Plug-and-Play – No VCDS, No ODIS, No Coding

Because we re-use the OEM LED driver boards, the central electrics module (J519) recognises the lamps as factory units the moment they are connected. There is no VCDS coding, no ODIS pass-through, and no aftermarket CAN-BUS module required. The clear-lens units drop straight into the factory connectors, and the existing wiring is reused. A first-time DIYer can complete the swap in about 30 minutes per side with a T20 Torx and a panel tool – that is the entire job.

What You Get in the Box

• 1 x Pair of Audi A6 C7 custom taillights – driver (left) and passenger (right) outer housings, Black Venom finish, clear lens, gloss black internal trim
• 1 x Pair of matching inner LED housings (trunk-lid units), Black Venom finish, ready to plug in
• Pre-installed OEM LED driver boards on fresh thermal pads (fixes the face-glow failure)
• Professional-grade sealant reseal on every housing (no butyl, no shortcut)
• Mounting hardware and gasket pre-fitted – no extra parts needed
• Printed install guide + 90-day warranty from delivery date

Fitment – Read This Before You Order

This Audi A6 C7 custom taillights set fits the Audi A6 / S6 C7.5 facelift sedan (2016-2018), including A6 2.0T, A6 3.0T, A6 3.0 TDI, S6 4.0T, and A6 Competition variants. It is not compatible with the pre-facelift C7 A6 / S6 (2012-2015) – that generation uses different outer part numbers and a different light signature. It is also not compatible with the Avant (wagon) body style – the Avant uses longer inner trunk-lid housings. Sedan only. If you are not sure which body style or generation you have, send us the last 8 digits of your VIN before ordering and we will confirm fitment.

Handmade Disclaimer – Important to Read

Every pair of Audi A6 C7 custom taillights we build here is handcrafted on a per-order basis using genuine OEM cores. Each Audi A6 C7 custom taillights set is individually tested before dispatch. Because each unit is built by hand, small variations between individual pieces (lens clarity, trim finish depth, gasket seating) are normal and expected – they are not defects and are not grounds for refund or return under our handmade-custom policy. Production time is typically 5-8 business days before dispatch. We will not ship a set we are not proud to put our name on.

Each item is handcrafted from genuine used OEM cores and is not a genuine Audi part. Audi, Audi A6, Audi S6, and the four-ring logo are registered trademarks of Audi AG / Volkswagen AG. This product is not endorsed by or affiliated with Audi AG.